Reseller Zone Knowledgebase VoIP Server Routers and networks Quality of Service (QoS): DSCP, TOS and precedence chart

Quality of Service (QoS): DSCP, TOS and precedence chart

Print
0

Routers and phones ask for QoS values in different forms: some want a DSCP number, some a TOS value in decimal or hex, some a precedence. They are all ways of writing the same byte. Use this guide to turn the value you have into the one your device asks for.

Updated 8 November 2026Applies to any router, firewall or phone

For voice on our services, use

46DSCP
EFDSCP class
184TOS
0xB8TOS in hex

Mark both SIP and RTP this way. On NBN services, voice marked outside DSCP 40 to 47 is dropped.

One byte, read two ways

Every packet carries one QoS byte. Current equipment reads its first six bits as the DSCP value. Older equipment reads the whole byte as TOS, with the first three bits as the precedence. Neither changes the bits, only how they are written down.

The voice packet's QoS byte, 10111000, read as DSCP 46 (EF) and as TOS 184 (0xB8), precedence 5The voice value, 10111000, read both ways.

How to use the chart

  1. Find the value you have

    Look along the row for the column your value is in: DSCP, DSCP class, TOS or precedence.

  2. Read across to the one you need

    Every value on the same row describes the same marking. A device that asks for "DiffServ" or "DSCP" wants the DSCP column; one that asks for "TOS" or "IP precedence" wants the TOS columns.

  3. Check the format

    Some devices want hex (0xB8), some decimal (184). The value is the same.

Tip: the voice row is highlighted in the chart below.

The full chart

DSCPDSCP classDSCP hexDSCP binaryTOSTOS hexTOS binaryPrecedencePrecedence nameDTR
0-0x0000000000x00000000000Routine000
1-0x0100000140x04000001000Routine001
2-0x0200001080x08000010000Routine010
3-0x03000011120x0C000011000Routine011
4-0x04000100160x10000100000Routine100
8CS10x08001000320x20001000001Priority000
10AF110x0A001010400x28001010001Priority010
12AF120x0C001100480x30001100001Priority100
14AF130x0E001110560x38001110001Priority110
16CS20x10010000640x40010000002Immediate000
18AF210x12010010720x48010010002Immediate010
20AF220x14010100800x50010100002Immediate100
22AF230x16010110880x58010110002Immediate110
24CS30x18011000960x60011000003Flash000
26AF310x1A0110101040x68011010003Flash010
28AF320x1C0111001120x70011100003Flash100
30AF330x1E0111101200x78011110003Flash110
32CS40x201000001280x80100000004FlashOverride000
34AF410x221000101360x88100010004FlashOverride010
36AF420x241001001440x90100100004FlashOverride100
38AF430x261001101520x98100110004FlashOverride110
40CS50x281010001600xA0101000005Critical000
44VOICE-ADMIT0x2C1011001760xB0101100005Critical100
46EF0x2E1011101840xB8101110005Critical110
48CS60x301100001920xC0110000006InterNetworkControl000
56CS70x381110002240xE0111000007NetworkControl000

D, T and R are the old TOS delay, throughput and reliability flags. Chart based on information compiled by D. Tucny.

What's next

Was this guide helpful?

Still stuck?

Send us the details and our team will take it from here

Open a Support Ticket